How Do You Fix a Noisy Washing Machine When Spinning

TANYA ILIEVA - AUGUST 19, 2026

📖 Reading time: 13 minutes and 59 seconds

There is a particular moment in the laundry cycle when an otherwise civilised appliance can appear to develop ambitions of becoming industrial machinery. The drum accelerates, a low vibration grows through the floor, and suddenly the washing machine is thumping against the cabinet, rattling something mysterious behind it, or attempting a slow migration across the utility room.

The spin cycle naturally creates more vibration than gentler stages of the wash because the drum is rotating at high speed while carrying several kilograms of wet laundry. Depending on the programme and model, modern domestic machines commonly reach 1,200 to 1,600 revolutions per minute. At 1,400 rpm, the drum completes more than 23 rotations every second. A towel, duvet cover or pair of jeans gathered heavily on one side can therefore create a considerable imbalance.

That gives us the first clue. A noisy washing machine during the spin cycle does not necessarily mean an expensive mechanical failure. Load distribution, levelling, installation, trapped objects and the floor beneath the appliance can all transform normal mechanical vibration into surprisingly intrusive noise. Manufacturers including Bosch, Samsung and AEG consequently place these simple checks among their first troubleshooting recommendations.

The kind of sound matters just as much as its volume, however. A repetitive thump tells a different story from a metallic scrape, and a machine that vibrates through the floor presents a different problem from one producing a deep roar inside the drum. Before reaching for the toolbox, listen.

Get Free Consultation

Key Takeaways And Quick Wins

Start with the simplest possibilities because several common spin-cycle problems can be checked within minutes.

Pause and redistribute the laundry if the machine begins banging or shaking heavily.
Check that all four feet are firmly supported and use a spirit level rather than judging by eye.
Look for loose objects around the drum, door seal and accessible filter.
Check the hoses and surrounding cabinetry for anything touching the machine and rattling with it.
Confirm that transit bolts have been removed if the appliance is new or has recently been installed.
Stop using the machine and investigate further when you hear persistent grinding, scraping or roaring, or notice leakage, a burning smell, excessive drum play or severe movement.

A useful distinction will save considerable troubleshooting time. Sound travels through the air to your ears, while vibration travels mechanically through the appliance, floor, walls and surrounding furniture before some of that energy becomes audible again. A washing machine can therefore create a noise problem even when its motor and drum are operating normally.

And that explains why the spin cycle deserves special attention.

Why The Spin Cycle Finds Every Weak Point

During washing, the drum turns relatively slowly, lifting and dropping clothes through water. Spinning has a very different purpose. The machine accelerates the drum rapidly so centrifugal action drives water out of the textiles and through the perforations in the drum.

The engineering challenge lies in keeping that rotating mass centred.

Inside a typical front-loading machine, the inner drum sits within an outer tub supported by springs and dampers or shock absorbers. Counterweights add stability. Bearings allow the drum to rotate, while a motor, belt and pulley arrangement, or a direct-drive motor on some machines, supplies rotational force.

When everything is working correctly, those systems control the considerable forces created during spinning. Add an uneven load, a loose foot or a flexible timber floor, and part of that energy finds another route.

One Wet Towel Can Change The Physics

Wet textiles rarely distribute themselves like laboratory weights. A bath mat can retain far more water than a lightweight T-shirt, while a duvet cover has an almost supernatural ability to swallow smaller garments and create one heavy bundle.

As rotational speed rises, an off-centre mass produces forces that repeatedly pull the drum away from its ideal axis. The suspension tries to control the movement, the cabinet responds, and the floor receives the remaining vibration.

Modern machines commonly detect imbalance and attempt to redistribute the load before reaching full spin speed. Bosch, for example, notes that its unbalanced-load detection can interrupt spinning when laundry is distributed unevenly.

The first diagnostic tool, then, is your ear.

Vibro-SMRV

The best seller

View Product

Listen To The Noise Before Trying To Fix It

A washing machine has a surprisingly broad vocabulary, and different sounds point towards different areas of the appliance.

Banging And Heavy Thumping

A regular thump-thump-thump that intensifies as the drum accelerates commonly points towards an unbalanced load, an unstable machine or excessive movement within the suspension system.

Pause the cycle and redistribute the clothes. Large and small items should have enough room to move rather than forming one dense mass. Bosch specifically warns that both overloading and underloading can contribute to problems, and recommends leaving approximately a hand's width of free space at the top of the drum for a normal load.

If redistribution immediately calms the machine, you have probably found the culprit. Persistent heavy banging with ordinary balanced loads deserves a closer look at levelling and suspension.

Rattling And Metallic Knocking

Rattling often has a more mundane origin. Coins, keys, buttons, zips, belt buckles and underwires can strike the drum or become trapped around the seal or filter. A hose touching the rear cabinet can also turn ordinary vibration into a remarkably convincing mechanical rattle.

AEG advises checking the drum, accessible drain filter, hoses and small garments or objects when investigating spin noise.

Empty pockets remain one of the cheapest forms of appliance maintenance ever invented.

Grinding, Scraping And Roaring

A persistent grinding or scraping sound requires greater caution because internal components may be involved. Drum bearings, the pulley system, foreign objects between drum components, or other rotating parts can produce mechanical noise that becomes most obvious at high spin speed.

A deep roar that rises with drum speed can be associated with bearing wear. The diagnosis should consider other symptoms too, including roughness when the drum is rotated manually, excessive play, leakage or changes in the way the drum sits within the machine.

Those signs take us beyond laundry distribution and towards mechanical inspection.

Vibro-EPMS

The best seller

View Product

Check The Load Before Checking The Machine

If the noise appeared suddenly during a particular wash, begin with the contents of the drum.

Pause the programme safely and wait until the door can be opened according to the manufacturer's instructions. Separate any bundle of clothing, untangle sheets and redistribute heavier pieces around the drum. If one extremely heavy item dominates the load, adding suitable items or removing some laundry may allow the machine to balance more effectively.

Pay particular attention to:

bath mats and thick towels
jeans and heavy cotton garments
bedding that can trap smaller items inside
a single bulky garment
very small loads with one relatively heavy item
an overloaded drum with too little space for movement

AEG notes that even one item can unbalance a machine during spinning, just as an overloaded drum can.

Run another spin and listen. If the machine settles, the diagnosis has cost you nothing. If the cabinet continues to shake, the next suspect sits underneath it.

A Few Millimetres At The Feet Can Become A Room-Sized Problem

A washing machine needs all four feet to make firm contact with a stable surface. One poorly adjusted foot allows the cabinet to rock, and high-speed rotation repeatedly excites that movement.

Place a spirit level across the top of the appliance from side to side and front to back. Adjust the feet according to the manufacturer's manual until the cabinet sits level and cannot rock when gently pressed at opposite corners. Locking nuts should then be secured where the design requires them.

Both Bosch and Samsung recommend levelling as a primary response to excessive vibration. Samsung also advises checking that all four feet maintain secure contact with the floor.

Then Look Beneath The Feet

A rigid concrete slab and a flexible timber floor behave very differently.

Timber joists and floorboards can flex under a rapidly changing load. Once the forcing frequency from the machine approaches a resonant behaviour of the floor structure, vibration can become much more noticeable elsewhere in the room. The appliance may be technically level while the building itself helps amplify its movement.

Bosch specifically identifies wooden floors as problematic for washing-machine vibration and recommends a hard surface, with additional floor reinforcement in suitable installations.

This distinction matters when considering anti-vibration pads or mats. A resilient layer can help reduce some structure-borne vibration when the appliance is already correctly installed. It cannot straighten a rocking machine, redistribute laundry or repair a failed bearing.

Before buying anything, therefore, make sure the source itself is behaving correctly.

Vibro-Tile

The best seller

View Product

The Tiny Objects Capable Of Producing Enormous Drama

A metallic tapping sound that appears once per drum revolution can come from something remarkably small.

Inspect the visible drum carefully with a torch. Run your fingers gently around the rubber door seal when the appliance is switched off and safe to inspect, looking for coins, clips or other debris. Follow the manufacturer's instructions for accessing and cleaning the drain filter, because small objects can travel through the system and reach the pump area.

If the noise appears mainly while water is being pumped away, drainage deserves particular attention. AEG notes that drain-hose routing, restrictions, cabinet contact and foreign objects around the pump can all create unusual draining noises. A steady pump hum, meanwhile, can form part of normal operation.

This is why timing matters. A rattle during every drum rotation points in one direction, while a grinding sound appearing only when the pump runs points somewhere else.

There is one installation mistake, however, that can make a perfectly new machine sound alarmingly unhealthy from its first spin.

Transit Bolts Can Turn The First Wash Into A Percussion Performance

Front-loading washing machines are transported with bolts that secure the drum assembly and protect it while the appliance is being moved. Those restraints are intended for transport and must be removed during installation according to the machine's instructions.

If they remain fitted, the suspended tub cannot move as designed, so vibration can transfer much more directly into the cabinet.

Samsung states that its front-load machines may have three to five shipping bolts, depending on model, and both Samsung and Bosch identify unremoved bolts as a cause of excessive noise and vibration.

A newly installed machine that shakes violently therefore deserves an installation check before any mechanical diagnosis. Keep removed transit bolts somewhere sensible too. Manufacturers may recommend refitting them when the appliance is transported again.

Once installation, load and loose objects have been ruled out, the character of the investigation changes.

When Banging Comes From The Suspension

The tub inside a washing machine is deliberately allowed to move. Springs support its weight while dampers or shock absorbers control excessive oscillation as the drum accelerates and decelerates.

Over time, these components can wear. A damper that has lost resistance allows greater tub movement, which can produce pronounced banging during spinning even when the machine is level and correctly loaded.

Top-loading machines use different suspension arrangements depending on design, including rods, springs or straps. The principle remains similar: the rotating assembly needs controlled movement.

Possible warning signs include repeated heavy movement across several ordinary loads, a tub that appears unusually loose, or banging that continues after basic installation and balance checks.

Replacing suspension components ranges from relatively accessible to decidedly awkward depending on the model. At this point, the appliance manual, manufacturer service information and your own repair experience matter. Disconnecting power and water before internal work is essential, and uncertainty is a perfectly good reason to call a qualified appliance technician.

A roar or grind, meanwhile, can point deeper into the rotating assembly.

Bearing Noise Usually Tells A More Expensive Story

Drum bearings allow the inner drum to rotate smoothly while supporting substantial radial loads. Thousands of wash cycles expose them to repeated mechanical stress, and seal failure can eventually allow moisture into the bearing assembly.

A failing bearing often announces itself gradually. The machine may develop a low rumble that grows into a pronounced roar during high-speed spinning, sometimes described as an aeroplane or jet-engine sound.

A Simple Check Before Calling A Technician

With the machine switched off, disconnected from the mains and empty, rotate the drum gently by hand. Listen for rough grinding and feel for uneven resistance. Depending on the machine design, excessive movement when carefully lifting the drum may also warrant professional investigation.

These observations can support a diagnosis, although they cannot identify every internal fault with certainty.

Bearing replacement can involve substantial disassembly, and on some models the design of the tub makes the repair especially labour-intensive. The decision then becomes economic as well as mechanical. Consider the machine's age, overall condition, parts availability, labour cost and the price of a suitable replacement before approving a major repair.

And bearings are only one part of the drivetrain capable of making itself heard.

Belts, Pulleys And Motors Have Their Own Soundtrack

Many washing machines transfer motor power to the drum through a drive belt and pulley. Wear, misalignment, or looseness can create squealing, rhythmic thumping or changes in sound as rotational speed rises. Other designs use direct-drive systems and therefore have a different set of potential faults.

A persistent motor-related whine, electrical smell, visible belt damage, repeated error codes or failure to reach normal spin speed calls for model-specific diagnosis. Internal access also introduces electrical, mechanical and water-related hazards, so repair decisions should follow the manufacturer's service guidance.

At this stage, randomly replacing parts becomes an expensive troubleshooting strategy. A professional diagnosis can be cheaper than purchasing a procession of components that were innocent all along.

There is another possibility worth considering before blaming the appliance. Sometimes the washing machine is producing ordinary vibration and the room is enthusiastically broadcasting it.

F-MUTE Floor Soundproofing panel for noise insulation system DECIBEL

F-MUTE SYSTEM™ - GRINDŲ GARSO IZOLIACIJA

The best seller

View Product

Your Floor Can Turn Vibration Into Noise Elsewhere In The House

A spinning washing machine generates mechanical energy at its feet. On a rigid, massive floor, much of that energy remains localised. Lightweight or flexible structures can transmit vibration through joists, floorboards and adjoining surfaces, where panels and furniture may radiate the vibration back into the room as audible sound.

This is structure-borne noise, and it explains the peculiar experience of a washing machine sounding more intrusive in another room than beside the appliance itself.

A cupboard panel may buzz. Pipework can rattle against a wall. A lightweight floor can develop a low-frequency resonance. The machine becomes the source, while the building becomes part of the loudspeaker.

First, Remove Accidental Contact

Check the clearances recommended by the appliance manufacturer. Make sure hoses, cables and the cabinet are not repeatedly striking walls, cupboards or pipework. AEG specifically identifies hose-to-cabinet contact as one route through which vibration can be amplified.

Then Consider Vibration Isolation

Once the machine is mechanically healthy, correctly levelled and installed on a suitable base, resilient isolation products can help reduce the transfer of vibration into the structure.

The important word is isolation. Soft material placed beneath an unstable appliance can introduce additional movement, so the isolation solution must suit the machine, its mass, its operating behaviour and the supporting floor.

This is where appliance troubleshooting meets acoustics.

Reducing Washing Machine Noise Requires Control At The Source And Along The Path

A wall covered with acoustic material will never repair a worn bearing. Equally, repairing the washing machine may still leave an intrusive structure-borne noise problem when vibration is efficiently travelling into a lightweight floor or adjoining wall.

The useful acoustic question therefore becomes where is the energy travelling?

For airborne sound, the path is through the air and building partitions. For structure-borne vibration, energy travels through solid connections. Effective noise control begins by identifying the dominant route and intervening there.

For a mechanically healthy washing machine, practical measures may include:

maintaining the manufacturer's required clearance around the appliance
preventing hoses and cabinets from creating rigid vibration bridges
improving the rigidity of an unsuitable supporting floor where appropriate
using correctly selected resilient vibration isolation
addressing weak acoustic separation between a utility area and adjoining living or sleeping spaces when appliance noise remains intrusive

A washing machine installed beside a bedroom presents a different acoustic problem from one sitting on a concrete utility-room floor. The appliance may be identical while the transmission path changes completely.

That is precisely why the loudness alone cannot diagnose the problem.

Vibro-R

The best seller

View Product

When Should You Stop The Machine And Call A Professional

A sudden change in sound deserves attention, particularly when accompanied by another symptom. Stop the cycle safely and arrange professional assessment when you encounter persistent grinding or scraping, violent movement after load and levelling checks, water leakage, a burning smell, electrical symptoms, substantial drum play, repeated fault codes or an inability to drain or spin correctly.

Manufacturer support guidance similarly recommends professional diagnosis when basic installation and troubleshooting measures fail, especially when abnormal noise accompanies poor draining, leaks, error codes or other mechanical symptoms.

The age of the appliance should form part of the repair decision rather than determining it alone. A seven-year-old machine with a minor replaceable component may have plenty of useful life ahead. The same machine facing an expensive bearing or major drivetrain repair deserves a comparison between repair cost, condition, efficiency, parts availability and replacement value.

A technician can diagnose the component. You still decide which investment makes sense.

The Most Useful Diagnostic Tool Might Be Your Phone

Here is one final trick that appliance manuals rarely turn into a habit.

When a strange sound appears, record it.

Capture 20 to 30 seconds of video showing the machine as it enters the noisy part of the spin cycle. Record a second clip from farther away if vibration is travelling through the floor or wall. Note the programme, approximate load and the exact stage at which the sound begins.

Why bother? Because intermittent faults have an inconvenient habit of behaving perfectly when a technician arrives. A recording preserves the rhythm and character of the noise, while the timing can help distinguish drum rotation from pump operation, cabinet vibration or a transient imbalance.

There is an acoustic lesson here too. Once you begin listening for how a washing machine makes noise rather than simply how loud it sounds, the problem becomes easier to separate into source, vibration and transmission path. That same distinction applies to countless noises around the home, from plumbing and ventilation to lifts, boilers and the mysterious neighbour whose furniture apparently moves only after midnight.

Perhaps the washing machine has one final useful job beyond cleaning clothes. It can teach us how buildings carry sound.

Frequently Asked Questions

Why Is My Washing Machine Suddenly Loud During The Spin Cycle?

A sudden increase in spin noise can come from an unbalanced load, a trapped object, an unstable foot, hose contact or a developing mechanical fault. Start with the load and installation checks, then investigate further if the sound persists across different washes.

How Do I Rebalance A Washing Machine Drum?

Pause the programme safely, allow the door to unlock, and redistribute tangled or heavy items around the drum. Large and small items should have enough space to move freely, and a single heavy item may need to be removed or balanced with suitable additional laundry.

How Can I Tell If The Drum Bearings Are Wearing Out?

A deep rumbling or roaring sound that becomes substantially stronger as spin speed rises can indicate bearing wear. With the empty machine disconnected from the mains, roughness during gentle hand rotation or unusual drum movement can provide further clues, although professional inspection gives a more reliable diagnosis.

Why Does My Washing Machine Sound Like A Jet Engine?

The description commonly refers to a deep, rapidly increasing roar during high-speed spinning. Worn bearings are one possible cause, while drivetrain problems, installation conditions and transmitted structural vibration can create similar impressions, so the accompanying symptoms matter.

Can A Clogged Filter Make A Washing Machine Noisy?

Yes. Coins, buttons and other objects can reach an accessible drain filter or pump area and produce rattling or grinding during drainage. Follow the manufacturer's manual when opening and cleaning the filter because residual water may be present.

Why Does My Washing Machine Shake More On A Wooden Floor?

Timber floors can flex and transmit vibration more readily than a rigid concrete base. The floor may also resonate with forces generated during spinning, making vibration noticeable across a wider part of the building. Bosch specifically identifies wooden floors as a potential contributor to washing-machine vibration.

Do Anti-Vibration Pads Make Washing Machines Quieter?

They can reduce some vibration transmission when correctly selected and used beneath a stable, mechanically healthy machine. They cannot correct an unbalanced load, failed suspension, worn bearings, remaining transit bolts or poor levelling, so those causes should be addressed first.

Is It Safe To Keep Using A Washing Machine That Makes A Loud Noise?

The answer depends on the sound and accompanying symptoms. Normal pump hum and brief balance adjustments can be part of ordinary operation, while persistent grinding, severe banging, leakage, burning smells or substantial movement justify stopping the appliance and arranging further investigation.

Get Free Consultation